Product help with community knowledge
2013
Simulation Moldflow
HomeSimulation MoldflowEnglish2013HelpInsightProcess settingsInclude part insert

Simulation Moldflow

2012
2013
Help
Installation and Licensing
Insight
Autodesk Simulation Moldflow Insight Help
Visual Learning
Release notes
Tutorials
Getting Started
User Interface
Import and Export
Modeling
The mesh
Molding processes
Analysis sequence
Materials and databases
Process settings
Process settings (Procedure)
Profiles
Pack/Holding Control Profile Settings dialog
%Filling pressure vs time
Packing pressure vs time
Hydraulic pressure vs time
%Maximum machine pressure vs time
Pressure control points
Process controller
Process controller dialog-Profile/Switch-Over Control tab
Filling control
Velocity/pressure switch-over
Pack/holding control
Process controller dialog-Temperature Control tab
Mold temperature control
Mold surface temperature
Melt temperature
Ambient temperature
Process controller dialog-MPX Profile Data tab
Imported profile data
Process controller for Reactive Injection-compression molding dialog-Time Control (Fill) tab
Mold-open time
Process controller dialog-Time Control (Fill + Pack) tab
Cooling time
[Specified] of
Mold-open time
Process controller dialog-Time Control (Cool) tab
Injection + packing + cooling time
Injection + packing + cooling time
Mold-open time
Process controller dialog-Co-injection Control tab
Switch to the other controller by
Process controller dialog-Microcellular Control tab
Volume filled at start of foaming
Initial bubble radius
Number of cells per volume
Initial gas concentration
Process controller for Reactive Injection-compression molding dialog-Measured Profiles tab
Imported profile data
Process controller for Reactive Injection-compression molding dialog-Time Control (Flow) tab
Mold-open time
Process controller for Reactive Injection-compression molding dialog-Transfer Pot tab
Pellet diameter
Pellet length
Transfer pot temperature
Delay time in the pot
Process controller for Reactive Injection-compression molding dialog-Curing Phase tab
Melt initial conversion
Curing time
%Air Mass
Injection molding machine
Injection molding machine dialog
Description tab
Trade name
Manufacturer
Data source
Date last modified
Data status
Injection Unit tab
Maximum machine injection stroke
Maximum machine injection rate
Machine screw diameter
Filling control
Ram speed control steps
Pressure control steps
Hydraulic Unit tab
Machine pressure limit
Intensification ratio
Machine hydraulic response time
Clamping Unit tab
Maximum machine clamp force
Do not exceed maximum clamp force
Solver parameters
Number of laminae across thickness
Mold-melt Heat Transfer Coefficient (HTC) option
Heat transfer coefficient between pot and pellet (side)
Heat transfer coefficient between pot and pellet (bottom)
Number of laminates across beam radius
Mold-melt Heat Transfer Coefficient (HTC) values (3D)
Intermediate Output tab
Dynamically update results display during analysis
Filling/packing phase intermediate results
Number of regular results
Number of profiled intermediate results in filling/packing phase
Number of regular results
Results Output Settings dialog
Write filling/packing phase regular results at
Write filling/packing phase profiled results at
RTM/SRIM solver parameters (Midplane/Dual Domain) dialog-Convergence tab
Pressure convergence tolerance
Flow rate convergence tolerance
Melt temperature convergence tolerance
Conversion convergence tolerance
Maximum number of melt temperature iterations
Maximum number of flow rate iterations
Maximum number of melt temperature and conversion iterations
Nodal growth mechanism
Viscosity treatment at high shear rates
Restart tab
Number of restart steps in filling phase
Number of restart steps in packing phase
Include part insert
Mesh model only interface
ANSYS options dialog
Cool Solver Parameters dialog
Method for calculating geometric influence
value
Mold temperature convergence tolerance
Maximum number of mold temperature iterations
Number of time steps for 3D cooling flux calculation
Include runners in automatic cooling time calculations
Use aggregated mesh solver
Calculate internal mold temperatures
Warpage analysis type
Stress result(s) to output
Consider gate surface and cold runners?
Include cold runners
Consider mold thermal expansion
Consider corner effects
Matrix solver
AMG matrix solver selection
Use mesh aggregation and 2nd-order tetrahedral elements/mesh options
Interface to other structural analysis
Number of threads for parallelization
Fiber Analysis tab dialog
Calculate fiber orientation using
Apply fiber inlet condition at
Fiber inlet condition
Edge boundary condition
Composite property calculation options
MuCell Analysis tab dialog
Number of iterations for bubble growth calculation
Core Shift tab dialog
Perform Core shift analysis
Frequency of Core shift analysis
Insert temperature
Analyze core using
Perform Core shift analysis during pressure iteration
Update mesh during Core shift analysis
Calculate Core shift after filling phase
Surface matching tolerance
Percentage frozen layer that makes node constrained
Use AMG matrix solver
Stress analysis type
Perform wire sweep/paddle shift simulation in
Dynamic Paddle Shift tab
Frequency of Core shift analysis
Perform Core shift analysis during pressure iteration
Update mesh during Core shift analysis
Calculate Core shift after filling phase
Analyze core using
Use AMG matrix solver
Fill+Pack Analysis tab dialog
Intermediate results
Recovery data
Hours
Microchip Options tab dialog
Stress analysis type
Perform wire sweep/paddle shift simulation in
Viscosity cut-off temperature
Insert temperature
Venting analysis option
Vent size
Vent exit pressure (Gauge)
Minimum void volume option
Venting analysis locations grouping
Viscosity cut-off temperature
Solver Parameters (3D) dialog
Simulate inertia effect
Simulate gravity effect
GPU options
GPU options
Number of threads for parallelization
AMG matrix solver selection
Number of parallel threads
Gate contact diameter for 3D models (part only)
Solver parameters
Filling Phase Solver Parameters dialog
Maximum %volume to fill per time step
Time step iteration controls
Packing/Curing Phase Solver Parameters dialog
Maximum packing time step
Time step iteration controls
Gravity Direction dialog
Orientation set
ANSYS Options dialog
Separate finite element mesh for mold
Specify filename dialog
Mold mesh model filename
Select part data to pass onto mold mesh
Solution method (ANSYS options)
Abaqus Options dialog
Generate interface to Abaqus
NASTRAN options dialog
Free format for .ist file
LS-DYNA Options dialog
Material model option (LS-DYNA options)
Solution method (LS-DYNA options)
Memory limit option (LS-DYNA options)
Element formulation option (LS-DYNA options)
Parallel process option (LS-DYNA options)
Optimization
Launching an analysis
Results
Reports
Reference materials
Troubleshooting guide
Application Programming Interface (API)
Glossary of Terms
Insight 360
Adviser
Communicator
Simulation TV
Videos
Community

Community Scoring

Was this page helpful?

Tag Tags0

This page has no tags

Page statistics

775 views,  1 edit(s),  557 characters(s) Page last modified 14:09, 5 Jun 2012 by contentconnector
How to add your knowledge

Include part insert

    Table of contents
    No headers

    This option determines if information relating to inserts is passed to the interface.

    The default for this option is YES. If the model includes a part insert, the insert will be accounted for in the model and result data passed to the interface.

    Comments0

    Powered by MindTouch
    © Copyright 2013 Autodesk, Inc. All rights reserved.   Privacy Policy — Legal Notices & Trademarks